| wpwrak | cladamw: you make reviewing your schematics a boring task | 00:51 |
|---|---|---|
| wpwrak | almost nothing bad to find :-( | 00:51 |
| wolfspraul | good morning everybody | 00:53 |
| cladamw | wpwrak, things would be all fun and be improved once discovered, but indeed. also thanks your cautiousness. | 00:57 |
| cladamw | wpwrak, nowadays i run Fped with *.fpd under /examples, still quite a bit unknown to play with. mostly needs geometry skills. | 01:00 |
| cladamw | wpwrak, need to pick a new one in m1r4 to practice. | 01:01 |
| wpwrak | cladamw: if you run find /where/all/your/qi-hw/projects/live -name \*.fpd | 01:06 |
| wpwrak | then you'll see all the footprints we already have. it's quite a lot. | 01:07 |
| wpwrak | not all are fully developed, though. e.g., some of the ones used for DIY may have the wrong surface on pads. for example, the mounting holes in labsw :) | 01:07 |
| GitHub11 | [board-m1] wpwrak pushed 1 new commit to master: https://github.com/milkymist/board-m1/commit/89d6752a53267122d8241a5a18f887d59ab039fe | 01:21 |
| GitHub11 | [board-m1/master] board-m1/dsv/: move dsv/ over from wernermisc/m1r4/dsv/ - Werner Almesberger | 01:21 |
| cladamw | wpwrak, tks for move dsv/ over, btw, do you have idea on categories for modules ? | 01:34 |
| cladamw | those modules we try to gather them under /kicad-lib/modules ? | 01:35 |
| wpwrak | perhaps it's best to do this just like we did with components: everything in one directory. then create a virtual hierarchy via some yet-to-be-written tool. | 01:37 |
| wpwrak | i don't have a specific hierarchy in mind yet. fped lets you combine lots of things in a single file, so you often handle what one may consider an entire category just in one file. | 01:38 |
| wpwrak | e.g., you could conceivably have a single file that generates all DIP packages, one for all QFNs, etc. (well, there are a few exotic QFNs that escape any systematic design, but they're rare) | 01:39 |
| wpwrak | you once asked about grounding the shell of the DMX receiver. according to http://en.wikipedia.org/wiki/DMX512#Electrical | 01:43 |
| wpwrak | we do this right: TX should be grounded, RX should have high impedance. so if you wanted to ground the RX side, it would have to be via one of those RC nets. | 01:44 |
| cladamw | so one DIP.fpd can included all like resistor, capacitor, and inductors but in names as R0402, R0603, R0508, C0402, L0805 etc. ? | 01:45 |
| cladamw | i opened those *.fpd, they are only one package in there, but you just meant likely a dip.fpd can gather R, C, L versitile packages ? | 01:47 |
| wpwrak | DIP would be for Dual-In-Line parts, e.g., ancient ICs ;-) | 01:48 |
| wpwrak | 0402 and such are in stdpass.fpd | 01:48 |
| cladamw | (E1.11 (DMX512 2004)) tks ! mm so m1 is correct. | 01:53 |
| wpwrak | looks like that. if there's a DMX expert here who disagrees, please speak up ;-) | 01:58 |
| GitHub142 | [milkymist-ng] sbourdeauducq pushed 1 new commit to master: http://git.io/kNJP_A | 08:27 |
| GitHub142 | [milkymist-ng/master] Common include files - Sebastien Bourdeauducq | 08:27 |
| GitHub27 | [milkymist-ng] sbourdeauducq pushed 1 new commit to master: http://git.io/eytStg | 08:44 |
| GitHub27 | [milkymist-ng/master] Get CSR base addresses from include file - Sebastien Bourdeauducq | 08:44 |
| GitHub161 | [milkymist-ng] sbourdeauducq pushed 2 new commits to master: http://git.io/jbJqEQ | 23:50 |
| GitHub161 | [milkymist-ng/master] Identifier - Sebastien Bourdeauducq | 23:50 |
| GitHub161 | [milkymist-ng/master] Update gitignore - Sebastien Bourdeauducq | 23:50 |
| --- Thu May 17 2012 | 00:00 | |
Generated by irclog2html.py 2.9.2 by Marius Gedminas - find it at mg.pov.lt!